Influence of bifilm defects generated during mould filling on the tensile properties of Al−Si−Mg cast alloys

Journal article

El-Sayed, M., Essa, K. and Hassanin, H. 2022. Influence of bifilm defects generated during mould filling on the tensile properties of Al−Si−Mg cast alloys. Metals. 12 (1), p. e160. https://doi.org/10.3390/met12010160
AuthorsEl-Sayed, M., Essa, K. and Hassanin, H.
AbstractEntrapped double oxide film defects are known to be the most detrimental defects during the casting of aluminium alloys. In addition, hydrogen dissolved in the aluminium melt was suggested to pass into the defects to expand them and cause hydrogen porosity. In this work, the effect of two important casting parameters (the filtration and hydrogen content) on the properties of Al−7 Si−0.3 Mg alloy castings was studied using a full factorial design of experiments approach. Casting properties such as the Weibull modulus and position parameter of the elongation and the tensile strength were considered as response parameters. The results suggested that adopting 10 PPI filters in the gating system resulted in a considerable boost of the Weibull moduli of the tensile strength and elongation due to the enhanced mould filling conditions that minimised the possibility of oxide film entrainment. In addition, the results showed that reducing the hydrogen content in the castings samples from 0.257 to 0.132 cm3/100 g Al was associated with a noticeable decrease in the size of bifilm defects with a corresponding improvement in the mechanical properties. Such significant effect of the process parameters studied on the casting properties suggests that the more careful and quiescent mould filling practice and the lower the hydrogen level of the casting, the higher the quality and reliability of the castings produced.
KeywordsBifilm; Al–7 Si–0.3 Mg alloy; Hydrogen; Filtration; Weibull modulus
Year2022
JournalMetals
Journal citation12 (1), p. e160
PublisherMDPI
ISSN2075-4701
Digital Object Identifier (DOI)https://doi.org/10.3390/met12010160
Official URLhttps://www.mdpi.com/2075-4701/12/1/160
Publication dates
Online16 Jan 2022
Publication process dates
Deposited10 Jan 2022
Accepted05 Jan 2022
Publisher's version
Output statusPublished
References

1. Campbell, J., Entrainment defects. Materials science and technology, 2006. 22(2): p. 127-145.
2. El-Sayed, F.H.B. and M.A., The effect of holding time before solidification on the properties of aluminium castings. The Journal of the Southern African Institute of Mining and Metallurgy, 2020. 120(8).
3. El-Sayed, M. and M. Ghazy, Entrained defects in light metal cast alloys. Journal of the Southern African Institute of Mining and Metallurgy, 2017. 117(7): p. 656-662.
4. Youssef, Y. and M. El-Sayed, Effect of reinforcement particle size and weight fraction on the mechanical properties of SiC particle reinforced Al metal matrix composites. International Review of Mechanical Engineering, 2016. 10(4).
5. El-Sayed, M., Effect of the Mould Rotational Speed on the Quality of Centrifugal Castings. International Journal of Applied Engineering Research, 2014. 9(21): p. 11575-11582.
6. El-Sayed, M.A., Effect of welding conditions on the mechanical properties of friction stir welded 1050 aluminum alloy. International Review of Mechanical Engineering, 2015. 9(3): p. 252-256.
7. Erzi, E., Ö. Gürsoy, Ç. Yüksel, M. Colak, and D. Dispinar, Determination of acceptable quality limit for casting of A356 aluminium alloy: supplier’s quality index (SQI). Metals, 2019. 9(9): p. 957.
8. Matejka, M., D. Bolibruchová, and R. Podprocká, The Influence of Returnable Material on Internal Homogeneity of the High-Pressure Die-Cast AlSi9Cu3 (Fe) Alloy. Metals, 2021. 11(7): p. 1084.
9. Neuser, M., O. Grydin, A. Andreiev, and M. Schaper, Effect of Solidification Rates at Sand Casting on the Mechanical Joinability of a Cast Aluminium Alloy. Metals, 2021. 11(8): p. 1304.
10. Souissi, N., S. Souissi, C.L. Niniven, M.B. Amar, C. Bradai, and F. Elhalouani, Optimization of squeeze casting parameters for 2017 a wrought al alloy using Taguchi method. Metals, 2014. 4(2): p. 141-154.
11. El-Sayed, M., H.G. Salem, A.-R. Kandeil, and W.D. Griffiths. A study of the behaviour of double oxide films in Al alloy melts. in Materials Science Forum. 2013. Trans Tech Publications Ltd.
12. El-Sayed, M.A., The behaviour of bifilm defects in cast Al-7Si-Mg alloy. PloS one, 2016. 11(8): p. e0160633.
13. El-Sayed, M.A. and K. Essa, Effect of mould type and solidification time on bifilm defects and mechanical properties of Al–7si–0.3 mg alloy castings. Computational and Experimental Studies, 2018. 6(4): p. 647-655.
14. Griffiths, W. and N.-W. Lai, Double oxide film defects in cast magnesium alloy. Metallurgical and materials transactions A, 2007. 38(1): p. 190-196.
15. Lai, N., W. Griffiths, and J. Campbell. Modelling of the potential for oxide film entrainment in light metal alloy castings. in Tenth International Conference on Modeling of Casting, Welding and Advanced Solidification Processes. 2003. Florida, USA: Warrendale, Pa. : Minerals, Metals & Materials Society.
16. Basuny, F.H., M. Ghazy, A.-R.Y. Kandeil, and M.A. El-Sayed, Effect of casting conditions on the fracture strength of Al-5 Mg alloy castings. Advances in Materials Science and Engineering, 2016. 2016.
17. El-Sayed, M., An investigation of the behaviour of double oxide film defects in aluminium-magnesium cast alloys. Journal of the Southern African Institute of Mining and Metallurgy, 2018. 118(11): p. 1225-1231.
18. Campbell, J., Castings. 2003: Elsevier.
19. El-Sayed, M.A., H.A. Salem, A.Y. Kandeil, and W. Griffiths, Determination of the lifetime of a double-oxide film in al castings. Metallurgical and Materials Transactions B, 2014. 45(4): p. 1398-1406.
20. El-Sayed, M.A.M., Double oxide film defects and mechanical properties in aluminium alloys. 2012, University of Birmingham.
21. Griffiths, W., A. Caden, and M. El‐Sayed. The Behaviour of Entrainment Defects in Aluminium Alloy Castings. in Proceedings of the 2013 International Symposium on Liquid Metal Processing and Casting. 2014. John Wiley & Sons, Inc.
22. Griffiths, W.D., A. Caden, and M. El-Sayed. An investigation into double oxide film defects in aluminium alloys. in Materials Science Forum. 2014. Trans Tech Publications Ltd.
23. Bahreinian, F., S. Boutorabi, and J. Campbell, Critical gate velocity for magnesium casting alloy (ZK51A). International Journal of Cast Metals Research, 2006. 19(1): p. 45-51.
24. Cox, M., M. Wickins, J. Kuang, R. Harding, and J. Campbell, Effect of top and bottom filling on reliability of investment castings in Al, Fe, and Ni based alloys. Materials Science and Technology, 2000. 16(11-12): p. 1445-1452.
25. Halvaee, A. and J. Campbell. Critical mold entry velocity for aluminum bronze castings. in One Hundred First Annual Meeting of the American Foundrymen's Society, Rosemont. 1997.
26. Runyoro, J., S. Boutorabi, and J. Campbell, Critical gate velocities for film-forming casting alloys: a basis for process specification. AFS Trans, 1992. 100: p. 225-234.
27. Dispinar, D. and J. Campbell, Critical assessment of reduced pressure test. Part 1: Porosity phenomena. International Journal of Cast Metals Research, 2004. 17(5): p. 280-286.
28. El-Sayed, M. and W. Griffiths, Hydrogen, bifilms and mechanical properties of Al castings. International Journal of Cast Metals Research, 2014. 27(5): p. 282-287.
29. El-Sayed, M., H. Hassanin, and K. Essa, Bifilm defects and porosity in Al cast alloys. The International Journal of Advanced Manufacturing Technology, 2016. 86(5-8): p. 1173-1179.
30. El-Sayed, M., H. Hassanin, and K. Essa, Effect of casting practice on the reliability of Al cast alloys. International Journal of Cast Metals Research, 2016. 29(6): p. 350-354.
31. Griffiths, W.D., A. Elsayed, and M.A. El-Sayed, Whisker formation in porosity in Al alloys. Metallurgical and Materials Transactions B, 2016. 47(6): p. 3459-3468.
32. Elsayed, M., M. Ghazy, Y. Youssef, and K. Essa, Optimization of SLM process parameters for Ti6Al4V medical implants. Rapid Prototyping Journal, 2019.
33. El-Sayed, M.A., K. Essa, M. Ghazy, and H. Hassanin, Design optimization of additively manufactured titanium lattice structures for biomedical implants. The International Journal of Advanced Manufacturing Technology, 2020: p. 1-12.
34. Hassanin, H., Y. Alkendi, M. Elsayed, K. Essa, and Y. Zweiri, Controlling the properties of additively manufactured cellular structures using machine learning approaches. Advanced Engineering Materials, 2020. 22(3): p. 1901338.
35. Hassanin, H., F. Modica, M.A. El‐Sayed, J. Liu, and K. Essa, Manufacturing of Ti–6Al–4V micro‐implantable parts using hybrid selective laser melting and micro‐electrical discharge machining. Advanced Engineering Materials, 2016. 18(9): p. 1544-1549.
36. Croarkin, C., P. Tobias, and C. Zey, Engineering statistics handbook. 2001, Gaithersburg, USA: The Institute Gaithersburg.
37. Weibull, W., A statistical distribution function of wide applicability. Journal of applied mechanics, 1951. 18(3): p. 293-297.
38. Green, N.R. and J. Campbell, Statistical distributions of fracture strengths of cast Al 7Si Mg alloy. Materials Science and Engineering: A, 1993. 173(1-2): p. 261-266.
39. El-Sayed, M.A., H.A. Salem, A.Y. Kandeil, and W. Griffiths, Effect of holding time before solidification on double-oxide film defects and mechanical properties of aluminum alloys. Metallurgical and Materials Transactions B, 2011. 42(6): p. 1104-1109.
40. Winardi, L., R. Griffin, H. Littleton, and J. Griffin, 08-130 Variables Affecting Gas Evolution Rates and Volumes from Cores in Contact with Molten Metal. Transactions of the American Foundrymen's Society, 2008. 116: p. 505.
41. Raiszadeh, R. and W. Griffiths, A method to study the history of a double oxide film defect in liquid aluminum alloys. Metallurgical and Materials Transactions B, 2006. 37(6): p. 865-871.
42. Nayak, A.K., D. Pal, and K. Santra, Ispaghula mucilage-gellan mucoadhesive beads of metformin HCl: Development by response surface methodology. Carbohydrate polymers, 2014. 107: p. 41-50.
43. Green, N. and J. Campbell, Influence of oxide film filling defects on the strength of Al-7Si-Mg alloy castings (94-114). Transactions of the American Foundrymen's Society, 1994. 102: p. 341-348.

Additional information

Publications router: Date 2022-01-05 of type 'accepted_date' included in notification.
Publications router: Date 2022-01-16 of type 'publication_date' with format 'electronic' included in notification
Publications router: Date 2022-01-05 of type 'accepted' included in notification
Publications router: Date 2022-01-16 of type 'pub-electronic' included in notification

Publications router: License for this article: https://creativecommons.org/licenses/by/4.0/ included in notification

Licensehttps://creativecommons.org/licenses/by/4.0/
Permalink -

https://repository.canterbury.ac.uk/item/8zzv3/influence-of-bifilm-defects-generated-during-mould-filling-on-the-tensile-properties-of-al-si-mg-cast-alloys

Download files

Publisher's version
metals-12-00160.pdf

  • 95
    total views
  • 50
    total downloads
  • 0
    views this month
  • 0
    downloads this month

Export as

Related outputs

A review of corncob-based building materials as a sustainable solution for the building and construction industry
Okeke, F., Ahmed, A., Imam, A. and Hassanin, H. 2024. A review of corncob-based building materials as a sustainable solution for the building and construction industry. Hybrid Advances. 6 (100269), pp. 1-16. https://doi.org/10.1016/j.hybadv.2024.100269
A novel enhanced SOC estimation method for lithium-ion battery cells using cluster-based LSTM models and centroid proximity selection
Al-Alawi, M., Jaddoa, A., Cugley, J. and Hassanin, H. 2024. A novel enhanced SOC estimation method for lithium-ion battery cells using cluster-based LSTM models and centroid proximity selection. Journal of Energy Storage. 97 (B), p. 112866. https://doi.org/10.1016/j.est.2024.112866
Assessment of compressive strength performance of corn cob ash blended concrete: a review
Okeke, F., Ahmed, A., Imam, A. and Hassanin, H. 2024. Assessment of compressive strength performance of corn cob ash blended concrete: a review. https://doi.org/10.18552/2024/SCMT/606
Tailoring 3D star-shaped auxetic structures for enhanced mechanical performance
Hassanin, H., Wang, Y., A. Alsaleh, N., Djuansjah, J., El-Sayed, K. and Essa, K. 2024. Tailoring 3D star-shaped auxetic structures for enhanced mechanical performance. Aerospace. 11 (6), p. 428. https://doi.org/10.3390/aerospace11060428
Virtual prototyping of vision-based tactile sensors design for robotic-assisted precision machining
Zaid, I., Sajwani, H., Halwani, M., Hassanin, H., Ayyad, A., AbuAssi, A., Almaskari, F., Abdul Samad, Y, Abusafieh, A. and Zweiri, Y. 2024. Virtual prototyping of vision-based tactile sensors design for robotic-assisted precision machining. Sensors and Actuators A: Physical. 374 (115469). https://doi.org/10.1016/j.sna.2024.115469
Designing lightweight 3D-printable bioinspired structures for enhanced compression and energy absorption properties
Harish, A., A. Alsaleh, N., Ahmadein, M., Elfar, A., Djuansjah, J., Hassanin, H., El-Sayed, M. and Essa, K. 2024. Designing lightweight 3D-printable bioinspired structures for enhanced compression and energy absorption properties. Polymers. 16 (6), p. 729. https://doi.org/10.3390/polym16060729
A novel vision-based multi-functional sensor for normality and position measurements in precise robotic manufacturing
Halwani, M., Ayyad, A., AbuAssi, L., Abdulrahman, Y., Almaskari, F., Hassanin, H., Abusafieh, A. and Zweiri, Y. 2024. A novel vision-based multi-functional sensor for normality and position measurements in precise robotic manufacturing. Precision Engineering. 88, pp. 367-381. https://doi.org/10.1016/j.precisioneng.2024.02.015
Optimisation of a novel hot air contactless single incremental point forming of polymers
Almadani, M., Guner, A., Hassanin, H. and Essa, K. 2024. Optimisation of a novel hot air contactless single incremental point forming of polymers. Journal of Manufacturing Processes. 117, pp. 302-314. https://doi.org/10.1016/j.jmapro.2024.02.042
Advancing safety and efficiency in critical infrastructure with a novel SOC estimation for battery storage systems: A focus on second life batteries
Al-Alawi, M., Cugley, J., Jaddoa, A. and Hassanin, H. 2024. Advancing safety and efficiency in critical infrastructure with a novel SOC estimation for battery storage systems: A focus on second life batteries.
Review on engineering of bone scaffolds using conventional and additive manufacturing technologies
Mohammed, A., Jiménez, Amaia, Bidare, Prveen, Elshaer, Amr, Memic, Adnan, Hassanin, Hany and Essa, Khamis 2024. Review on engineering of bone scaffolds using conventional and additive manufacturing technologies. 3D Printing and Additive Manufacturing. 11 (4), pp. 1418-1440. https://doi.org/10.1089/3dp.2022.0360
Contactless single point incremental forming: Experimental and numerical simulation
Almadani, M., Guner, A., Hassanin, H., De Lisi, Michele. and Essa, K. 2023. Contactless single point incremental forming: Experimental and numerical simulation. The International Journal of Advanced Manufacturing Technology. https://doi.org/10.1007/s00170-023-12401-1
Hot-air contactless single-point incremental forming
Almadani, M., Guner, A., Hassanin, H. and Essa, K. 2023. Hot-air contactless single-point incremental forming. Journal of Manufacturing and Materials Processing. 7 (5), p. 179. https://doi.org/10.3390/jmmp7050179
Optimising surface roughness and density in titanium fabrication via laser powder bed fusion
Hassanin, H., El-Sayed, M., Ahmadein, M., A. Alsaleh, N., Ataya, S., Ahmed, M. and Essa, K. 2023. Optimising surface roughness and density in titanium fabrication via laser powder bed fusion. Micromachines. 14 (8), p. 1642. https://doi.org/10.3390/mi14081642
Hybrid finite element–smoothed particle hydrodynamics modelling for optimizing cutting parameters in CFRP composites
Abena, A., Ataya, S., Hassanin, H., El-Sayed, M., Ahmadein, M., A. Alsaleh, N., Ahmed, M. and Essa, K. 2023. Hybrid finite element–smoothed particle hydrodynamics modelling for optimizing cutting parameters in CFRP composites. Polymers. 15 (13), p. 2789. https://doi.org/10.3390/polym15132789
Embracing sustainable farming: Unleashing the circular economy potential of second-life EV batteries in agricultural applications
Al-Alawi, M., Cugley, J. and Hassanin, H. 2023. Embracing sustainable farming: Unleashing the circular economy potential of second-life EV batteries in agricultural applications.
Entrained defects and mechanical properties of aluminium castings
El-Sayed, M., Essa, K. and Hassanin, H. 2023. Entrained defects and mechanical properties of aluminium castings.
Preparation of polylactic acid/calcium peroxide compo-site filaments for fused deposition modelling
Mohammed, A., Kovacev , N., Elshaer, A., Melaibari, A., Iqbal, J., Hassanin, H., Essa, K. and Memić, A. 2023. Preparation of polylactic acid/calcium peroxide compo-site filaments for fused deposition modelling. Polymers. 15 (9), p. 2229. https://doi.org/10.3390/polym15092229
Non-destructive disassembly of interference fit under wear conditions for sustainable remanufacturing
Yeung, H., Ataya, S., Hassanin, H., El-Sayed, M., Ahmadein, M., A. Alsaleh, N., Ahmed, M. and Essa, K. 2023. Non-destructive disassembly of interference fit under wear conditions for sustainable remanufacturing. Machines. 11 (5), p. 538. https://doi.org/10.3390/machines11050538
Fabrication and characterization of oxygen-generating polylactic acid/calcium peroxide composite filaments for bone scaffolds
Mohammed, A., Saeed, A., Elshaer, A., Melaibari, A., Memić, A., Hassanin, H. and Essa, K. 2023. Fabrication and characterization of oxygen-generating polylactic acid/calcium peroxide composite filaments for bone scaffolds. Pharmaceuticals. 16 (4), p. 627. https://doi.org/10.3390/ph16040627
Using second-life batteries and solar power to help farms become energy efficient.
Al-Alawi, M., Cugley, J. and Hassanin, H. 2023. Using second-life batteries and solar power to help farms become energy efficient. Canterbury Christ Church University.
Chip formation and orthogonal cutting optimisation of unidirectional carbon fibre composites
Hassanin, H., Abena, A., Soo, L., Ataya, S., El-Sayed, M., Ahmadein, M., A. Alsaleh, N., Ahmed, M. and Essa, K. 2023. Chip formation and orthogonal cutting optimisation of unidirectional carbon fibre composites. Polymers. 15 (8), p. 1897. https://doi.org/10.3390/polym15081897
Fabrication and Optimisation of Ti-6Al-4V Lattice-Structured Total Shoulder Implants Using Laser Additive Manufacturing
Bittredge, Oliver, Hassanin, H., El-Sayed, M., Eldessouky, Hossam Mohamed, A. Alsaleh, N., Alrasheedi, Nashmi H., Essa, K. and Ahmadein, M. 2022. Fabrication and Optimisation of Ti-6Al-4V Lattice-Structured Total Shoulder Implants Using Laser Additive Manufacturing. Materials (Basel, Switzerland). 15 (9), p. e3095. https://doi.org/10.3390/ma15093095
Elastomer-based visuotactile sensor for normality of robotic manufacturing systems
Hassanin, H., Zaid, I., Halwani, M., Ayyad, A., Imam, A., Almaskari, F. and Zweiri, Y. 2022. Elastomer-based visuotactile sensor for normality of robotic manufacturing systems. Polymers. 14 (23), p. 5097. https://doi.org/10.3390/polym14235097
Techno-economic feasibility of retired electric-vehicle batteries repurpose/reuse in second-life applications: A systematic review
Hassanin, H., Al-Alawi, M. and Cugley, J. 2022. Techno-economic feasibility of retired electric-vehicle batteries repurpose/reuse in second-life applications: A systematic review. Energy and Climate Change. 3 (100086). https://doi.org/10.1016/j.egycc.2022.100086
Planning, operation, and design of market-based virtual power plant considering uncertainty
Hassanin, H., Ullah, Z., Arshad, Cugley, J. and Al-Alawi, M. 2022. Planning, operation, and design of market-based virtual power plant considering uncertainty. Energies. 19 (15), p. 7290. https://doi.org/10.3390/en15197290
The epistemic insight digest: Issue : Autumn 2022
Gordon, A., Shalet, D., Simpson, S., Hassanin, H., Lawson, F., Lawson, M., Litchfield, A., Thomas, C., Canetta, E., Manley, K. and Choong, C. Shalet, D. (ed.) 2022. The epistemic insight digest: Issue : Autumn 2022. Canterbury Canterbury Christ Church University.
Modeling, optimization, and analysis of a virtual power plant demand response mechanism for the internal electricity market considering the uncertainty of renewable energy sources
Ullah, Z., Arshad and Hassanin, H. 2022. Modeling, optimization, and analysis of a virtual power plant demand response mechanism for the internal electricity market considering the uncertainty of renewable energy sources. Energies. 15 (14), p. 5296. https://doi.org/doi.org/10.3390/en15145296
Interdisciplinary engineering education - essential for the 21st century
Gordon, A., Simpson, S. and Hassanin, H. 2022. Interdisciplinary engineering education - essential for the 21st century.
Multipoint forming using hole-type rubber punch
Hassanin, H., Tolipov, A., El-Sayed, M., Eldessouky, H., A. Alsaleh, N., Alfozan, A., Essa, K. and Ahmadein, M. 2022. Multipoint forming using hole-type rubber punch. Metals. 12 (3), p. 491. https://doi.org/10.3390/met12030491
Multistage Tool Path Optimisation of Single-Point Incremental Forming Process
Yan, Zhou, Hassanin, H., El-Sayed, M., Eldessouky, Hossam Mohamed, Djuansjah, Joy Rizki Pangestu, A. Alsaleh, N., Essa, K. and Ahmadein, M. 2021. Multistage Tool Path Optimisation of Single-Point Incremental Forming Process. Materials (Basel, Switzerland). 14 (22), p. e6794. https://doi.org/10.3390/ma14226794
Effect of runner thickness and hydrogen content on the mechanical properties of A356 alloy castings
El-Sayed, M., Essa, K. and Hassanin, H. 2021. Effect of runner thickness and hydrogen content on the mechanical properties of A356 alloy castings . International Journal of Metalcasting. https://doi.org/10.1007/s40962-021-00753-x
Parts design and process optimization
Hassanin, Hany, Bidare, Prveen, Zweiri, Yahya and Essa, Khamis 2021. Parts design and process optimization. in: Salunkhe, S., Hussein, H. and Davim, J. (ed.) Applications of Artificial Intelligence in Additive Manufacturing USA IGI Global. pp. 25-49
Micro-additive manufacturing technologies of three-dimensional MEMS
Hassanin, H., Sheikholeslami, G., Pooya, S. and Ishaq, R. 2021. Micro-additive manufacturing technologies of three-dimensional MEMS . Advanced Engineering Materials. https://doi.org/10.1002/adem.202100422
Machine learning applied to the design and inspection of reinforced concrete bridges: Resilient methods and emerging applications
Fan , W., Chen, Y., Li, J., Sun, Y., Feng, F., Hassanin, H. and Sareh, P. 2021. Machine learning applied to the design and inspection of reinforced concrete bridges: Resilient methods and emerging applications. Structures. 33, pp. 3954-3963. https://doi.org/10.1016/j.istruc.2021.06.110
Porosity, cracks, and mechanical properties of additively manufactured tooling alloys: A review
Bidare, P., Jiménez, A., Hassanin, H. and Essa, K. 2021. Porosity, cracks, and mechanical properties of additively manufactured tooling alloys: A review. Advances in Manufacturing. https://doi.org/10.1007/s40436-021-00365-y
Laser powder bed fusion of Ti-6Al-2Sn-4Zr-6Mo alloy and properties prediction using deep learning approaches
Hassanin, H., Zweiri, Y., Finet, L., Essa, K., Qiu, C. and Attallah, M. 2021. Laser powder bed fusion of Ti-6Al-2Sn-4Zr-6Mo alloy and properties prediction using deep learning approaches. Materials. 14 (8), p. 2056. https://doi.org/10.3390/ma14082056
3DP printing of oral solid formulations: a systematic review
Brambilla, C., Okafor-Muo, O., Hassanin, H. and ElShaer, A. 2021. 3DP printing of oral solid formulations: a systematic review. Pharmaceutics. 13 (3), p. 358. https://doi.org/10.3390/pharmaceutics13030358
Powder-based laser hybrid additive manufacturing of metals: A review
Hassanin, H. 2021. Powder-based laser hybrid additive manufacturing of metals: A review. The International Journal of Advanced Manufacturing Technology.
Micro-fabrication of ceramics: additive manufacturing and conventional technologies
Hassanin, H., Essa, K., Elshaer, A., Imbaby, M. and El-Sayed, T. E. 2021. Micro-fabrication of ceramics: additive manufacturing and conventional technologies. Journal of Advanced Ceramics. 10, pp. 1-27. https://doi.org/10.1007/s40145-020-0422-5
4D Printing of origami structures for minimally invasive surgeries using functional scaffold
Langford, T, Mohammed, A., Essa, K., Elshaer, A. and Hassanin, H. 2020. 4D Printing of origami structures for minimally invasive surgeries using functional scaffold. Applied Sciences. 11 (1), p. 332. https://doi.org/10.3390/app11010332
Reconfigurable multipoint forming using waffle-type elastic cushion and variable loading profile
Hassanin, H., Mohammed, M., Abdel-Wahab, A. and Essa, K 2020. Reconfigurable multipoint forming using waffle-type elastic cushion and variable loading profile. Materials.
3D printing of solid oral dosage forms: numerous challenges with unique opportunities
Hassanin, H. 2020. 3D printing of solid oral dosage forms: numerous challenges with unique opportunities. Journal of Pharmaceutical Sciences. https://doi.org/10.1016/j.xphs.2020.08.029
Design optimisation of additively manufactured titanium lattice structures for biomedical implants
El-Sayed, M.A., Essa, K., Ghazy, M. and Hassanin, H. 2020. Design optimisation of additively manufactured titanium lattice structures for biomedical implants. The International Journal of Advanced Manufacturing Technology. https://doi.org/10.1007/s00170-020-05982-8
4D Printing of NiTi auxetic structure with improved ballistic performance
Hassanin, H., Abena, A., Elsayed, M.A. and Essa, K. 2020. 4D Printing of NiTi auxetic structure with improved ballistic performance. Micromachines. 11 (8), p. 745. https://doi.org/doi.org/10.3390/mi11080745